- #Tool as crosshair in mastercam x4 manual
- #Tool as crosshair in mastercam x4 software
- #Tool as crosshair in mastercam x4 windows
Since this drawing is symmetrical in the X-axis you will only draw half of the total part and use the mirror function to complete the part. Repeat this command to make it visible again. From the keyboard, press Alt + O keys simultaneously to hide it.
The Operations Manager to the left of the screen can be hidden to gain more space in the graphic area for design. See Getting started page A-6 for further information. It will show you where the part origin is. See Getting started page A-4 for details. GEOMETRY CREATION Setting up the Graphic User Interface Before starting the geometry creation we should customize the toolbars to see the toolbars required to create the geometry and machine a 2D part. Running the Verify function to machine the part on the screen. The Student will check the toolpath using Mastercam’s Verify module by: Defining a 3-dimensional rectangular block the size of the workpiece. Chamfer the top of profile using chamfer contour. Second Setup An open pocket to machine the inside material. The Student will create 2-dimensional milling toolpaths consisting of: First Setup 4 holes drilled through the part. Mirroring existing geometry to complete the part. Creating arcs knowing the diameter and the center point. Trimming 1 entity to another existing entity. Creating parallel lines defining the offset direction and distance. The Student will design a 2-dimensional wireframe drawing by: Creating a rectangle knowing the width and the height of the rectangle. TUTORIAL #2 LEVEL 1 - 2D GEOMETRY DRILLING, OPEN POCKET, OPEN CONTOUR & CHAMFER CONTOUR TOOLPATHS 2-1 Tutorial #3, 2D Geometry, Extrude, Sweep, Modify a Face Draft Angle, Chamfer, Fillet. 1-1 Tutorial #2, 2D Geometry, Revolve, Extrude, Chamfer, Fillet and Modify. Solids Tutorials Tutorial #1, 2D Geometry, Extrude Create Body, Extrude Cut Body, Chamfer and Fillet. 1-1 Tutorial #2, 2D Geometry, Face, Rough, Finish, Grooving & Drilling. Lathe Tutorials Tutorial #1, 2D Geometry, Face, Rough and Finish. B-6 Setting The Cplane and Tplane to +D+Z. 5-1 Tutorial #6, 2D Geometry, Pocket with an Island & Circle Mill. 4-1 Tutorial #5, 2D Geometry, Dynamic Mill &Transform Toolpaths. 3-1 Tutorial #4, 2D Geometry, Drill, Slot Mill & 2D HS Core Mill. 2-1 Tutorial #3, 2D Geometry, Tapping, Contouring, Pocketing and Save Operations. 1-1 Tutorial #2, 2D Geometry, Drill, Open Pocket, Open Contour and Chamfer. Mill Tutorials Tutorial #1, 2D Geometry, Open Contour and Drilling.
#Tool as crosshair in mastercam x4 windows
Microsoft, the Microsoft logo, MS, and MS-DOS are registered trademarks of Microsoft Corporation Windows2000, Windows XP, are registered trademarks of Microsoft Corporation. Trademarks Mastercam is a registered trademark of CNC Software, Inc. This document may not, in whole or part, be copied, photocopied, reproduced, translated or reduced to any electronic medium or machine readable form without prior consent, in writing, from In-House Solutions Inc.
#Tool as crosshair in mastercam x4 manual
Copyrights This manual is protected under the copyright laws of Canada and the United States. Some jurisdictions do not allow the exclusion or limitation of implied warranties or liability for incidental or consequential damages, so the above limitation or exclusion may not apply to you. has been advised of the possibility of such damages. be liable for direct, indirect, or consequential damages resulting from any defect in the manual, even if InHouse Solutions Inc. Should the manual prove defective following its purchase, the buyer (and not In-House Solutions Inc., its distributor, or its retailer) assumes the entire cost of all necessary servicing, repair, of correction and any incidental or consequential damages. manual is sold or licensed "as is." The entire risk as to its quality and performance is with the buyer.
#Tool as crosshair in mastercam x4 software
makes no warranties, either express or implied, with respect to this manual or with respect to the software described in this manual, its quality, performance, merchantability, or fitness for any particular purpose. Disclaimer Of All Warranties And Liability In-House Solutions Inc. reserves the right to make improvements to this manual at any time and without notice. Software: Mastercam X Mill, Lathe & Solids Authors: Mariana Lendel ISBN: 978-1-92 Notice In-House Solutions Inc. Mastercam X Beginner Training Tutorials – Mill, Lathe & Solids Applications Date: JCopyright © 1984 - 2009 In-House Solutions Inc. To order more books: Call 1-80 or Visit or Contact your Mastercam Dealer
0 kommentar(er)
